Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 130

background image

This section provides instructions on how to replace the power supply assembly.

Although there are no moving parts in your server after the power cord has been disconnected, the following
warnings are required for your safety and proper Underwriters Laboratories (UL) certification.

DANGER

Hazardous moving parts. Keep fingers and other body parts away.

CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label
attached. There are no serviceable parts inside these components. If you suspect a problem with
one of these parts, contact a service technician.

To replace the power supply assembly, do the following:

1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all

power cords from electrical outlets and disconnect all cables that are connected to the server.

2. Remove the server cover. See “Removing the server cover” on page 25.

3. Lay the server on its side and disconnect the power supply assembly cables from the system board and

all drives. See “Locating parts on the system board” on page 17.

Installing, removing, or replacing hardware

43

«
...
53
54
55
56
57
...
»

Содержание ThinkServer TS130 1098



































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TS130 1098

x3100 M5 Type 5457

Бренд: IBM Страницы: 688

Sun Fire X2100 M2

Бренд: Sun Microsystems Страницы: 128

ANR-C62-N1 Series

Бренд: Acrosser Technology Страницы: 57

Бренд: Integra Страницы: 40

DiskStation Series

Бренд: Synology Страницы: 6

SuperServer 1029U-T Series

Бренд: Supermicro Страницы: 1

Бренд: Advantech Страницы: 38

SILVERSTREAM 3.75

Бренд: RSA Security Страницы: 11

ExtremeControl IA-A-305

Бренд: Extreme Networks Страницы: 31

Бренд: Extreme Networks Страницы: 94

Бренд: Promise Technology Страницы: 80

Бренд: Viavi Страницы: 8

Бренд: Black Box Страницы: 48

Бренд: DM&P Group Страницы: 27

LANTIME/SHS/BGT

Бренд: Meinberg Страницы: 5

LANTIME M600 MRS

Бренд: Meinberg Страницы: 160

SuperStorageSystem SSG-2028R-DN2R24L

Бренд: Supermicro Страницы: 82

TwinPro 1029TP-DC0R

Бренд: Supermicro Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды