Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 102

Страница: 102 / 130

POST error code

POST error message

Description/Action

0211

Keyboard not found

This error message is displayed when there is no
keyboard detected.

0135

Fan failure

The system might be overheating.

Press F1 to enter the Setup Utility program. Then
press F10 to save the operation and exit the Setup
Utility program.

Note:

If the problem is caused by the

microprocessor fan, pressing F10 will not solve
the problem.

0164

Memory size decreased

This error message is displayed when the memory
size has decreased.

Press F1 to enter the Setup Utility program. Then
press F10 to save the operation and exit the Setup
Utility program.

1762

Configuration change has occurred

This error message is displayed when a hard disk
drive or optical drive change has been made.

Press F1 to enter the Setup Utility program. Then
press F10 to save the operation and exit the Setup
Utility program.

1820

More than one external fingerprint reader
is attached. Power off and remove all but
the reader that you set up within your main
operating system.

If more than one external fingerprint reader is
connected to a computer, this error message will
be displayed to inform you to remove all of the
fingerprint keyboards except the one compatible
with the fingerprint application on your computer.

1962

No operating system found. Press any key
to repeat boot sequence.

This error occurs only after the POST is completed.
Press any key to repeat boot sequence.

0162

Setup data integrity check failure

Press F1 to enter the Setup Utility program. Then
press F10 to save the operation and exit the Setup
Utility program.

0167

No processor microcode update found

This error message indicates that there is
no microcode update image for the current
microprocessor.

0175

System security - Security data corrupted

Press F1 to enter the Setup Utility program. Then
press F10 to save the operation and exit the Setup
Utility program.

0176

System security - The system has been
tampered with

This error message is displayed when the
computer is turned on with the cover open or
removed.

Press F1 to enter the Setup Utility program. Then
press F10 to save the operation and exit the Setup
Utility program.

0189

System security - Can not read the
Security EEPROM

This error message indicates that the Security
EEPROM might be broken or have been removed.

Press F1 to enter the Setup Utility program. Then
press F10 to save the operation and exit the Setup
Utility program.

ThinkServer TS130 Hardware Maintenance Manual

Содержание ThinkServer TS130 1098



































































































































Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды

Lenovo ThinkServer TS130 1098, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды