Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 62

Страница: 62 / 130

6. Insert the two tabs

of the new front fan assembly into the corresponding holes in the chassis, and

press the other two tabs

through the holes until the front fan assembly is secured in place.

Figure 36. Installing the front fan assembly

7. Connect the new front fan assembly cable to the power fan connector on the system board. See

“Locating parts on the system board” on page 17.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the replacement, go to “Completing the parts replacement” on page 58.

Replacing the rear fan assembly

Attention:

Do not open your server or attempt any repair before reading and understanding “Safety information”

on page iii and “Guidelines” on page 23.

This section provides instructions on how to replace the rear fan assembly.

To replace the rear fan assembly, do the following:

1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all

power cords from electrical outlets and disconnect all cables that are connected to the server.

2. Remove the server cover. See “Removing the server cover” on page 25.

3. Locate the rear fan assembly. See “Internal components” on page 18.

ThinkServer TS130 Hardware Maintenance Manual

Содержание ThinkServer TS130 1098



































































































































Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды

Lenovo ThinkServer TS130 1098, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды