Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 29

Страница: 29 / 130

Locating parts on the system board

Figure 6 “System board part locations” on page 17 shows the locations of the parts on the system board.

Figure 6. System board part locations

4-pin power connector

Front panel connector for power switch and LED indicators

Microprocessor fan connector

Front USB connector 1 (for connecting USB port 1 and 2

on the front bezel)

Memory slot 1 (DIMM1)

Front USB connector 2 (for connecting additional USB

devices)

Memory slot 2 (DIMM2)

Clear CMOS (Complementary Metal Oxide Semiconductor)

/Recovery jumper

Memory slot 3 (DIMM3)

Internal speaker connector

Memory slot 4 (DIMM4)

Front audio connector (for connecting the microphone and

headphone connectors on the front bezel)

Thermal sensor connector

PCI card slots (2)

24-pin power connector

PCI Express x1 card slot

Battery

PCI Express x16 card slot

SATA connectors 1 and 2 (SATA 3.0

connectors)

Rear fan connector

SATA connector 3 (SATA 2.0 connector)

Cover presence switch connector (Intrusion switch connector)

eSATA connector

Microprocessor

Front fan connector

PS/2 keyboard and mouse connector

Chapter 4

Locating parts, controls, and connectors

Содержание ThinkServer TS130 1098



































































































































Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды

Lenovo ThinkServer TS130 1098, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды