Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 130

background image

Chapter 2. Server setup road map

This chapter provides a general road map to guide you through the setup and configuration of your server.

The server setup procedure varies depending on the configuration of the server when it was delivered. In
some cases, the server is fully configured and you just need to connect the server to the network and an
electrical outlet, and then you can turn on the server. In other cases, the server needs to have hardware
features installed, requires hardware and firmware configuration, and requires the operating system to
be installed.

Table 1. Server setup road map

Task

Where to find the information

Unpack

“Server package” on page 7

Install hardware

Chapter 5 “Installing, removing, or replacing hardware” on page 23

Connect the Ethernet cable
and power cord

“Rear view” on page 14

Turn on the server to verify
operation

“Turning on the server” on page 60

Review the BIOS settings
and customize as needed

“Starting the Setup Utility program” on page 63

Configure Redundant Array
of Independent Disks (RAID)

“Configuring RAID” on page 79

Check for firmware updates

“Updating the firmware” on page 81

Install the operating system
and basic drivers

“ThinkServer EasyStartup” on page 10

Install any additional drivers
needed for added features

Refer to the instructions that came with the hardware option.

Configure Ethernet settings
in the operating system

See the operating system help. This step is not required if the operating system was
installed using the ThinkServer EasyStartup program.

Install applications

Refer to the documentation that comes with the applications that you want to install.

© Copyright Lenovo 2011, 2015

5

«
...
15
16
17
18
19
...
»

Содержание ThinkServer TS130 1098



































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TS130 1098

Express5800/T110g-S

Бренд: NEC Страницы: 34

ML-2010 - B/W Laser Printer

Бренд: Samsung Страницы: 25

eServer BladeCenter JS20 Type 8842

Бренд: IBM Страницы: 150

Бренд: Premio Страницы: 3

SBXL52 - Server Compute Blade

Бренд: Intel Страницы: 126

SUPERO SuperServer 1018L-MP

Бренд: Supermicro Страницы: 104

Бренд: BlueNet Video Страницы: 38

SuperServer 6019P-WT

Бренд: Supermicro Страницы: 133

Бренд: Synology Страницы: 24

Бренд: IBM Страницы: 96

Бренд: QNAP Страницы: 39

Бренд: Planet Страницы: 83

Бренд: Leightronix Страницы: 22

Бренд: Imagine Страницы: 2

Бренд: ImageQuest Страницы: 31

IMS LANTIME M3000

Бренд: Meinberg Страницы: 139

Бренд: ClearView Страницы: 42

Бренд: GeoVision Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды