Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 130

background image

• Built-in monitoring for fan, temperature, and voltage

• Cooling fans with speed-sensing capability

• ECC DDR3 SDRAM with Serial Presence Detect (SPD)

• Error codes and messages to help you identify problems

• Generating error logs for the power-on self-test (POST) failures

• Hot-swap SAS hard disk drives

• Integrated Ethernet controllers

• Intelligent Platform Management Interface (IPMI) 2.0

• Power-on self-test (POST)

• Standby voltage for system-management features and monitoring

• System-error light-emitting diode (LED) on the front panel

• Vital product data (VPD), including the serial number information and replacement part numbers, stored in

the nonvolatile memory for easier remote maintenance

Software

This topic provides information about the software programs that you can use to set up, use, and maintain
the server.

ThinkServer EasyStartup

The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported
operating systems and device drivers on your server. This program is provided with your server on
a self-starting (bootable)

ThinkServer EasyStartup

DVD. The user guide for the program also is on the

DVD and can be accessed directly from the program interface. For detailed information, see “Using the
ThinkServer EasyStartup program” on page 82.

ThinkServer EasyUpdate Firmware Updater

The ThinkServer EasyUpdate Firmware Updater program (hereinafter referred to as the Firmware Updater
program) enables you to maintain your server firmware up-to-date and helps you avoid unnecessary server
outages. The Firmware Updater program is available for downloading from the Lenovo Support Web site.
For more information about downloading and using the Firmware Updater program, see “Updating the
firmware” on page 81.

BIOS update utilities

The BIOS firmware keeps updating after the shipment of the server. Lenovo maintains pages on the Support
Web site and provides the BIOS update utilities with instructions for download to help you update the
BIOS firmware if needed. For more information, see “Updating the firmware” on page 81 and “Updating
system programs” on page 85.

RAID configuration utilities

Your server supports onboard SATA software Redundant Array of Independent Disks (RAID). For detailed
information, see “Configuring RAID” on page 79.

Diagnostic programs

The following diagnostic programs are available for you to diagnose server problems:

• ThinkServer Diagnostic Tool

10

ThinkServer TS130 Hardware Maintenance Manual

«
...
20
21
22
23
24
...
»

Содержание ThinkServer TS130 1098



































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TS130 1098

Power 720 Express 8202-E4B

Бренд: IBM Страницы: 64

Бренд: IBM Страницы: 148

Бренд: IBM Страницы: 36

Бренд: IBM Страницы: 834

Enterprise Server

Бренд: Blackberry Страницы: 88

Бренд: AXIOMTEK Страницы: 55

Бренд: Altos Страницы: 93

Бренд: Rohde & Schwarz Страницы: 126

Бренд: PRG Страницы: 50

PUZZLE-IN004 Series

Бренд: IEI Technology Страницы: 102

Бренд: Advantech Страницы: 140

Бренд: Acer Страницы: 52

Бренд: Acer Страницы: 94

Altos R700 Series

Бренд: Acer Страницы: 135

Бренд: Acer Страницы: 10

Бренд: Acer Страницы: 148

Бренд: Acer Страницы: 108

Бренд: Acer Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды