Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 130

background image

Deleting RAID volumes

This section describes how to use the Intel Matrix Storage Manager option ROM configuration utility to
delete RAID volumes.

To delete RAID volumes, do the following:

1. Press Ctrl+I when prompted to enter the Intel Matrix Storage Manager option ROM configuration utility

during system startup.

2. Use the up and down arrow keys to select

Delete RAID Volume

and press Enter.

3. Use the arrow keys to select the RAID volume to be deleted and press Delete.

4. When prompted, press Y to confirm the deletion of the selected RAID volume. Deleting a RAID volume

will reset the hard disk drives to non-RAID.

5. After deleting a RAID volume, you can:

• Return to step 2 to delete additional RAID volumes.

• See “Creating RAID volumes” on page 80 for RAID volume creation.

• Use the up and down arrow keys to select

Exit

and press Enter.

Resetting disks to non-RAID

This section describes how to reset your hard disk drives to non-RAID.

To reset your hard disk drives to non-RAID, do the following:

1. Press Ctrl+I when prompted to enter the Intel Matrix Storage Manager option ROM configuration utility

during system startup.

2. Use the up and down arrow keys to select

Reset Disks to Non-RAID

and press Enter.

3. Use the arrow keys and the space key to mark individual physical hard disk drives to be reset, and then

press Enter to complete the selection.

4. When prompted, press Y to confirm the reset action.

5. After resetting the hard disk drives to non-RAID, you can:

• See “Deleting RAID volumes” on page 81 for RAID volume deletion.

• See “Creating RAID volumes” on page 80 for RAID volume creation.

• Use the up and down arrow keys to select

Exit

and press Enter.

Updating the firmware

The firmware in the server is periodically updated and the latest firmware is always available for downloading
from the Lenovo Web site.

Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to check for the latest
level of firmware, such as the BIOS updates and device drivers.

When you replace a device in the server, you might have to either update the server with the latest version of
the firmware that is stored in memory on the device or restore the preexisting firmware from a diskette or
CD image.

Notes:

• The BIOS ROM file is stored in flash on the system board.

• The onboard SATA software RAID firmware is integrated into the BIOS ROM on the system board.

.

Configuring the server

81

«
...
91
92
93
94
95
...
»

Содержание ThinkServer TS130 1098



































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TS130 1098

Бренд: Lantronix Страницы: 6

Бренд: Lantronix Страницы: 27

Z10 BUISNESS CLASS Z10 BC

Бренд: IBM Страницы: 67

x3450 - System - 7948

Бренд: IBM Страницы: 2

Бренд: Sun Fire Страницы: 66

Enterprise Server

Бренд: Blackberry Страницы: 88

Бренд: IESC Страницы: 109

Бренд: Lantech Страницы: 49

Бренд: Rackable Systems Страницы: 4

Бренд: Advantech Страницы: 96

PRIMERGY Econel 230R S1

Бренд: Fujitsu Страницы: 53

Primergy ECONEL 100 S2

Бренд: Fujitsu Страницы: 8

PRIMERGY Econel 200 S2

Бренд: Fujitsu Страницы: 65

PRIMERGY MX130 S1

Бренд: Fujitsu Страницы: 85

PRIMERGY Econel 100

Бренд: Fujitsu Страницы: 64

Бренд: Fujitsu Страницы: 105

Бренд: Fujitsu Страницы: 142

PRIMERGY GX2460 M1

Бренд: Fujitsu Страницы: 251

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды