Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 92

Страница: 92 / 130

Note:

The information about configuring RAID in this topic is applicable only in a Windows environment. For

information about configuring RAID in a Linux environment, contact your Linux software provider.

RAID level

Your server must have the minimum number of SATA hard disk drives installed for the supported level of
RAID to function:

• RAID Level 0 – Striped disk array

– Two hard disk drives minimum

– Better performance without fault tolerance

• RAID Level 1 – Mirrored disk array

– Two hard disk drives minimum

– Improved read performance and 100% redundancy

To install a secondary hard disk drive, refer to “Installing or replacing the secondary hard disk drive”
on page 39.

Configuring the system BIOS to enable SATA RAID functionality

This section describes how to configure the system BIOS to enable SATA RAID functionality.

Note:

Use the arrow keys on the keyboard to make selections.

To enable SATA RAID functionality, do the following:

1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 63.

2. Select

Devices

➙

ATA Drive Setup

3. Select

Configure SATA as

and press Enter.

4. Select

RAID Mode

and press Enter.

5. Press F10 to save changes and exit the Setup Utility program.

Creating RAID volumes

This section describes how to use the Intel Matrix Storage Manager option ROM configuration utility to
create RAID volumes.

To create RAID volumes, do the following:

1. Press Ctrl+I when prompted to enter the Intel Matrix Storage Manager option ROM configuration utility

during system startup.

2. Use the up and down arrow keys to select

Create RAID Volume

and press Enter.

3. Type a proper RAID volume name in the

Name

field and press Tab.

4. Use the arrow keys to select a RAID level in the

RAID Level

field and press Tab.

5. If appropriate, use the arrow keys to select a stripe size in the

Stripe Size

field and press Tab.

6. Type a volume size in the

Capacity

field and press Tab.

7. Press Enter to initiate volume creation.

8. When prompted, press Y to accept the warning message and create the volume.

9. If desired, return to step 2 to create additional RAID volumes.

10. When finished, select

Exit

and press Enter.

ThinkServer TS130 Hardware Maintenance Manual

Содержание ThinkServer TS130 1098



































































































































Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды

Lenovo ThinkServer TS130 1098, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды