Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 100

Страница: 100 / 130

• ThinkServer Diagnostic Tool

• ThinkServer System Profile Collection Tool

To use a diagnostic program, do the following:

1. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to locate a diagnostic

program.

2. Download and unzip the diagnostic program package to get the diagnostic program package folder.

3. Open the diagnostic program package folder and run the QTW.exe file.

4. Select the language when prompted. Then, click

Continue

5. Read the End User License Agreement (EULA) terms carefully and click

Accept

to start the program.

6. Follow the instructions on the screen to use the diagnostic program.

For detailed information about using a diagnostic program, refer to the user guide of the diagnostic program,
which is available for download at:
http://www.lenovo.com/drivers

Troubleshooting tables

Use the troubleshooting tables to find solutions to problems that have identifiable symptoms.

If you have just added new software or a new optional device and the server is not working, do the following
before using the troubleshooting tables:

1. Check the system-error LED on the operator information panel to see if it is lit.

2. Remove the software or device that you just added.

3. Run the diagnostic tests to determine whether the server is running correctly.

4. Reinstall the new software or new device.

Hard disk drive boot error

A hard disk drive boot error can have the following causes.

Symptom

FRU/Action

The startup drive is not in the boot sequence in
configuration.

Check the configuration and ensure the startup drive is
in the boot sequence.

No operating system is installed on the boot drive.

Install an operating system on the boot drive.

The boot sector on the startup drive is corrupted.

The drive must be formatted. Do the following:

1. Attempt to back up the data on the failing hard disk

drive.

2. Using the operating system programs, format the

hard disk drive.

The drive is defective.

Replace the hard disk drive.

Power supply problems

If you suspect a power supply problem, use the following procedures.

ThinkServer TS130 Hardware Maintenance Manual

Содержание ThinkServer TS130 1098



































































































































Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды

Lenovo ThinkServer TS130 1098, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды