Lenovo ThinkCentre E73 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 190

Lenovo ThinkCentre E73 Скачать руководство пользователя страница 96

7. Pull on the tips of the rubber mounts until the rear fan assembly is secured in place.

Figure 21. Installing the rear fan assembly

8. Connect the rear fan assembly cable to the system fan connector on the system board.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 122.

Replacing the battery

Attention:

Do not open your computer or attempt any repair before reading and understanding “Important safety information”
on page 1.

Your computer has a special type of memory that maintains the date, time, and settings for built-in features,
such as parallel-port assignments (configuration). A battery keeps this information active when you turn
off the computer.

The battery normally requires no charging or maintenance throughout its life; however, no battery lasts
forever. If the battery fails, the date, time, and configuration information (including passwords) are lost. An
error message is displayed when you turn on the computer.

Refer to the “Lithium battery notice” in the

ThinkCentre Safety and Warranty Guide

for information about

replacing and disposing of the battery.

To replace the battery, do the following:

92

ThinkCentre E73 Hardware Maintenance Manual

«
...
94
95
96
97
98
...
»

Содержание ThinkCentre E73































































































































































































Отзывы:

Нет отзывов