Lenovo ThinkCentre E73 Скачать руководство пользователя страница 161

Страница: 161 / 190

3. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 151.

Note:

Place the heat sink and fan assembly on its side so that the thermal grease on the bottom of it

does not get in contact with anything.

4. Locate the system board and disconnect all cables connected to the system board. See “Locating

parts on the system board” on page 79.

5. Lift the small handle

and open the retainer

to access the microprocessor

Figure 101. Accessing the microprocessor

6. Lift the microprocessor straight up and out of the microprocessor socket.

Figure 102. Removing the microprocessor

Notes:

a. Your microprocessor and socket might look different from the one illustrated.

Chapter 10

Replacing FRUs (machine types: 10AU, 10AW, 10BF, and 10BG)

157

Содержание ThinkCentre E73































































































































































































Результаты поиска

Содержание ThinkCentre E73

Отзывы:

Lenovo ThinkCentre E73, Руководство по техническому обслуживанию аппаратной части, Страница: 161 / 190

Результаты поиска

Содержание ThinkCentre E73

Отзывы: