Lenovo ThinkCentre E73 Скачать руководство пользователя страница 145

Страница: 145 / 190

Figure 81. Removing the slim card reader bracket

6. Remove the two screws that secure the card reader to the bracket. Then, slide the card reader as

shown to remove it from the bracket.

Note:

Touch only the edges of the card reader. Do not touch the circuit board of it.

Figure 82. Removing the slim card reader from the bracket

7. Take the new card reader out of the static-protective package by its sides.

8. Align the new card reader in the slim card reader bracket and slide the card reader into the rail as shown

until it stops. Then, install the two screws to secure the new card reader to the bracket.

Chapter 10

Replacing FRUs (machine types: 10AU, 10AW, 10BF, and 10BG)

141

Содержание ThinkCentre E73































































































































































































Результаты поиска

Содержание ThinkCentre E73

Отзывы:

Lenovo ThinkCentre E73, Руководство по техническому обслуживанию аппаратной части, Страница: 145 / 190

Результаты поиска

Содержание ThinkCentre E73

Отзывы: