Lenovo ThinkCentre E73 Скачать руководство пользователя страница 36

Страница: 36 / 190

Table 2. Programs in Control Panel (continued)

Program

Control Panel section

Green text in Control Panel

Rescue and Recovery

System and Security

Lenovo - Enhanced Backup and
Restore

System Update

System and Security

Lenovo - Update and Drivers

View Management Utility

System and Security

Lenovo View Management Utility

Note:

Depending on your computer model, some of the programs might not be available.

Accessing Lenovo programs on the Windows 8 operating system

If your computer is preinstalled with the Windows 8 operating system, you can access Lenovo programs
by doing the following:

Press the Windows key to go to the Start screen. Click a Lenovo program to launch it. If you cannot find the
program you need, move the pointer to the bottom-right corner of the screen to display the charms. Then
click the

Search

charm to search for the desired program.

Your computer supports the following Lenovo programs:

• Fingerprint Software

• Lenovo Companion

• Lenovo Solution Center

• Lenovo Support

• Password Manager

• System Update

Lenovo Support Web site

Technical support information is available on the Lenovo Support Web site at:
http://www.lenovo.com/support

This Web site is updated with the latest support information such as the following:

• Drivers and software

• Diagnostic solutions

• Product and service warranty

• Product and parts details

• User guides and manuals

• Knowledge base and frequently asked questions

ThinkCentre E73 Hardware Maintenance Manual

Содержание ThinkCentre E73































































































































































































Результаты поиска

Содержание ThinkCentre E73

Отзывы:

Lenovo ThinkCentre E73, Руководство по техническому обслуживанию аппаратной части, Страница: 36 / 190

Результаты поиска

Содержание ThinkCentre E73

Отзывы: