Lenovo ThinkCentre E73 Скачать руководство пользователя страница 104

Страница: 104 / 190

Figure 33. Installing the new slim card reader into the bracket

9. Route the cable of the new card reader through the corresponding hole for the card reader bracket in

the front of the chassis.

10. Install the bracket into the chassis so that the hole in the bracket is aligned with the corresponding hole

in the chassis. Then, Install the screw to secure the card reader bracket to the chassis.

Figure 34. Installing the slim card reader bracket

11. Connect the cable of the new slim card reader to the system board. See “Locating parts on the

system board” on page 72.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 122.

100

ThinkCentre E73 Hardware Maintenance Manual

Содержание ThinkCentre E73































































































































































































Результаты поиска

Содержание ThinkCentre E73

Отзывы:

Lenovo ThinkCentre E73, Руководство по техническому обслуживанию аппаратной части, Страница: 104 / 190

Результаты поиска

Содержание ThinkCentre E73

Отзывы: