manualshive.com logo in svg

Lenovo ThinkCentre E73, Руководство по техническому обслуживанию аппаратной части, Страница: 181 / 190

Поделиться
Скачать
Lenovo ThinkCentre E73 Скачать руководство пользователя страница 181

Chapter 11. Additional service information

This chapter provides additional information that the service representative might find helpful.

Security features

Security features in this section include the following:

• Passwords

• Vital Product Data

Hardware-controlled passwords

Use the Setup Utility program to set the hardware controlled passwords. For more information about
passwords, see “Using passwords” on page 55.

Operating system password

Note:

This section applies only to computer models that have an operating system preinstalled from Lenovo.

An operating system password is very similar to a power-on password and denies access to the computer by
an unauthorized user when the password is activated. The computer is unusable until the correct password
is entered and recognized by the computer.

Vital Product Data

Each computer has a unique Vital Product Data (VPD) code stored in the nonvolatile memory on the system
board. After you replace the system board, the VPD must be updated. To update the VPD, see “Flash
update procedures” on page 177.

BIOS levels

An incorrect level of BIOS can cause false errors and unnecessary FRU replacement. Use the following
information to determine the current level of BIOS installed in the computer, the latest BIOS available for the
computer, and where to obtain the latest level of BIOS.

• To determine the current Level of BIOS:

– Start the Setup Utility.
– Select Standard CMOS Features.

• Sources for obtaining the latest level BIOS available

1. Lenovo support web site:

http://www.lenovo.com/support/

2. Lenovo Customer Support Center
3. Levels 1 and 2 Support

To update (flash) the BIOS, see “Flash update procedures” on page 177.

Note:

BIOS settings vary by operating system. Change the BIOS settings before installing a new operating

system. See “Changing the BIOS settings before installing a new operating system” on page 59.

Flash update procedures

This section details how to flash (update) the BIOS.

© Copyright Lenovo 2013

177

Содержание ThinkCentre E73































































































































































































Отзывы:

Нет отзывов