Lenovo ThinkCentre E73 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 190

Lenovo ThinkCentre E73 Скачать руководство пользователя страница 186

Television output notice

The following notice applies to models that have the factory-installed television-output feature.

This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.

European conformance CE mark

Trademarks

The following terms are trademarks of Lenovo in the United States, other countries, or both:

Lenovo
The Lenovo logo
Rescue and Recovery
ThinkCentre
ThinkVantage

Microsoft, Windows, and Windows Media are trademarks of the Microsoft group of companies.

Other company, product, or service names may be trademarks or service marks of others.

182

ThinkCentre E73 Hardware Maintenance Manual

«
...
184
185
186
187
188
...
»

Содержание ThinkCentre E73































































































































































































Отзывы:

Нет отзывов