Lenovo ThinkCentre E73 Скачать руководство пользователя страница 153

Страница: 153 / 190

Note:

You might also need to release the power supply assembly cables from some cable clips or ties

that secure the cables to the chassis. Make sure that you note the cable routing before disconnecting
the cables.

6. At the rear of the computer, remove the three screws that secure the power supply assembly. Press the

power supply clip

downward to release the power supply assembly and then slide the power supply

assembly to the front of the computer. Lift the power supply assembly out of the computer.

Figure 93. Removing the power supply assembly

7. Ensure that the new power supply assembly is the correct replacement.

Chapter 10

Replacing FRUs (machine types: 10AU, 10AW, 10BF, and 10BG)

149

Содержание ThinkCentre E73































































































































































































Результаты поиска

Содержание ThinkCentre E73

Отзывы:

Lenovo ThinkCentre E73, Руководство по техническому обслуживанию аппаратной части, Страница: 153 / 190

Результаты поиска

Содержание ThinkCentre E73

Отзывы: