manualshive.com logo in svg

Lenovo ThinkCentre E73, Руководство по техническому обслуживанию аппаратной части, Страница: 144 / 190

Поделиться
Скачать
Lenovo ThinkCentre E73 Скачать руководство пользователя страница 144

11. Connect one end of the signal cable to the rear of the new optical drive and the other end to an available

SATA connector on the system board. See “Locating parts on the system board” on page 79. Then,
locate an available five-wire power connector and connect it to the rear of the new optical drive.

Figure 80. Connecting the optical drive

12. Lower the drive bay assembly.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 174.

Replacing the slim card reader

Attention:

Do not open your computer or attempt any repair before reading and understanding “Important safety information”
on page 1.

This section provides instructions on how to replace the slim card reader.

Note:

The slim card reader is only available in some models.

To replace the slim card reader, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 126.

3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 127.

4. Record the cable routing of the installed slim card reader and disconnect the cable of the slim card

reader from the system board.

5. Remove the screw that secures the slim card reader bracket and then remove the bracket from the

chassis.

140

ThinkCentre E73 Hardware Maintenance Manual

Содержание ThinkCentre E73































































































































































































Отзывы:

Нет отзывов