Lenovo ThinkCentre E73 Скачать руководство пользователя страница 38

Страница: 38 / 190

– Has this configuration ever worked?

– If it has been working, what changes were made prior to it failing?

– Is this the original reported failure?

• Diagnostics version

– Type and version level

• Hardware configuration

– Print (print screen) configuration currently in use

– BIOS level

• Operating system software

– Type and version level

Note:

To eliminate confusion, identical systems are considered identical only if they:

1. Are the exact machine type and models

2. Have the same BIOS level

3. Have the same adapters/attachments in the same locations

4. Have the same address jumpers/terminators/cabling

5. Have the same software versions and levels

6. Have the same diagnostic diskettes (version)

7. Have the same configuration options set in the system

8. Have the same setup for operating-system-controlled files

Comparing the configuration and software set-up between “working and non-working” systems will often
lead to problem resolution.

ThinkCentre E73 Hardware Maintenance Manual

Содержание ThinkCentre E73































































































































































































Результаты поиска

Содержание ThinkCentre E73

Отзывы:

Lenovo ThinkCentre E73, Руководство по техническому обслуживанию аппаратной части, Страница: 38 / 190

Результаты поиска

Содержание ThinkCentre E73

Отзывы: