manualshive.com logo in svg

Lenovo ThinkCentre E73, Руководство по техническому обслуживанию аппаратной части, Страница: 72 / 190

Поделиться
Скачать
Lenovo ThinkCentre E73 Скачать руководство пользователя страница 72

Locating connectors on the rear of your computer

Figure 2 “Rear connector locations” on page 68 shows the locations of the connectors on the rear of your
computer. Some connectors on the rear of your computer are color-coded to help you determine where to
connect the cables on your computer.

3

4

5

6

3 4

5 6

Figure 2. Rear connector locations

1

Power cord connector

8

Audio line-in connector

2

DisplayPort connector

9

PCI Express x16 graphics card slot

3

VGA monitor connector

10

PCI Express x1 card slots (2)

4

USB 3.0 connectors

11

Security-lock slot

5

USB 2.0 connectors

12

Padlock loop

6

Microphone connector

13

Optional serial port

7

Audio line-out connector

14

Ethernet connector

Connector

Description

Audio line-in connector

Used to receive audio signals from an external audio device, such as a stereo
system. When you attach an external audio device, a cable is connected between
the audio line-out connector of the device and the audio line-in connector of the
computer.

Audio line-out connector

Used to send audio signals from the computer to external devices, such as powered
stereo speakers (speakers with built-in amplifiers), headphones, multimedia
keyboards, or the audio line-in connector on a stereo system or other external
recording device.

DisplayPort connector

Used to attach a high-performance monitor, a direct-drive monitor, or other devices
that use a DisplayPort connector.

Ethernet connector

Used to attach an Ethernet cable for a local area network (LAN).

Note:

To operate the computer within FCC Class B limits, use a Category 5 Ethernet

cable.

68

ThinkCentre E73 Hardware Maintenance Manual

Содержание ThinkCentre E73































































































































































































Отзывы:

Нет отзывов