Lenovo 6241 Скачать руководство пользователя страница 1960 | Manualshive

Страница: 1960 / 1990

background image

User Response

Complete the following steps:

1. Update all firmware (including adapter firmware) to the latest levels.

2. If problem persists escalate to the next level of support.

•

W.3938002 A boot configuration error has been detected. Boot Configuration Error

Explanation:

A boot configuration error has been detected. Boot Configuration Error

Severity

Warning

User Response

Complete the following steps:

1. F1 Setup -> Save Settings

2. Retry OOB config update

•

W.50001 A DIMM has been disabled due to an error detected during POST. DIMM Disabled

Explanation:

A DIMM has been disabled due to an error detected during POST. DIMM Disabled

Severity

Info

User Response

Complete the following steps:

1. If the DIMM was disabled because of a memory fault, follow the procedure for that event.

2. If no memory fault is recorded in the logs and no DIMM connector error LEDs are lit, re-enable

the DIMM through the Setup utility or the Advanced Settings Utility (ASU).

3. If problem persists, Power cycle the node from management console.

4. Reset IMM to default settings.

5. Reset UEFI to default settings.

6. Reflash IMM and UEFI firmware.

7. Swap the DIMM from the disabled slot with a matching DIMM. If the slot remains disabled,

replace the compute book.

•

W.58001 The PFA Threshold limit (correctable error logging limit) has been exceeded on DIMM

number [arg1] at address [arg2]. MC5 Status contains [arg3] and MC5 Misc contains [arg4]. DIMM
PFA Threshold Exceeded

Explanation:

The PFA Threshold limit (correctable error logging limit) has been exceeded on DIMM

number [arg1] at address [arg2]. MC5 Status contains [arg3] and MC5 Misc contains [arg4]. DIMM PFA
Threshold Exceeded

Severity

Error

User Response

Complete the following steps:

1. If the node has recently been installed, moved, serviced, or upgraded, verify that the DIMM is

properly seated and visually verify that there is no foreign material in any DIMM connector on that
memory channel. If either of these conditions is found, correct and retry with the same DIMM.
(Note: Event Log may contain a recent 00580A4 event denoting detected change in DIMM
population that could be related to this problem.)

2. Check IBM support site for an applicable firmware update that applies to this memory error. The

release notes will list the known problems the update addresses. Also, check IBM support site

1946

System x3850 X6 and x3950 X6 Installation and Service Guide

«
...
1958
1959
1960
1961
1962
...
»

Содержание 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6241

Express5800/180Ra-7

Бренд: NEC Страницы: 2

Express5800/120Rh-2

Бренд: NEC Страницы: 2

Express5800/120Rh-2

Бренд: NEC Страницы: 2

Express5800/120Rg-1

Бренд: NEC Страницы: 2

Express5800/120Rf-1

Бренд: NEC Страницы: 21

Express5800/120Ra-1

Бренд: NEC Страницы: 6

Express5800/120Mc2 series

Бренд: NEC Страницы: 2

EXPRESS5800/120Le

Бренд: NEC Страницы: 56

Express5800 320La

Бренд: NEC Страницы: 8

Express5800 120Li

Бренд: NEC Страницы: 2

Express5800 120Ed

Бренд: NEC Страницы: 29

Active Upgrade Express5800/320Fc

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 10

Express5800/120Rj-2

Бренд: NEC Страницы: 18

Express5800/120Rh-1

Бренд: NEC Страницы: 20

Bull NovaScale R620 Series

Бренд: NEC Страницы: 346

Express5800 320La

Бренд: NEC Страницы: 206

Express5800/R110j-1

Бренд: NEC Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды