LEHNER Vento Скачать руководство пользователя | Manualshive

Страница: 27 / 52

background image

Maintenance and cleaning

Vento

®

1.0

27 / 52

Removing the rotary feeder shaft

1. Press pressure piece

(1)

of the shaft, turn to the

right and remove.

2. Pull out shaft

(2).

If not possible, please use the sup-

plied tool.

Cleaning rotary feeders

•

Pull the rotary feeders off the shaft and clean them. Check individual parts for damage and wear, renew if nec-

essary.

•

When dismantling the shaft, identify the sequence of components, and push back onto the shaft in reverse order

when assembling. During assembly, make sure that the rotary feeders are mounted offset in relation to one an-

other.

•

Rotary feeder shaft structure, see:

6.6.4 "Spare parts for rotary feeder shaft green, 1 x 2.5 ccm"
6.6.5 "Spare parts for rotary feeder shaft green, 2 x 2.5 ccm"
6.6.6 "Spare parts for rotary feeder shaft blue, 1 x 5.0 ccm"
6.6.7 "Spare parts for rotary feeder shaft blue, 2 x 5.0 ccm"
6.6.8 "Spare parts for rotary feeder shaft red, 1 x 10 ccm"
6.6.9 "Spare parts for rotary feeder shaft red, 2 x 10 ccm"

Installing the rotary feeder shaft

1. Insert the shaft into the holder as far as the stop.

If this is difficult (e.g. because the rotary feeder shaft is new), the supplied tool can be used as assistance, by

performing slight rotating movements.

2. Put on the cover and turn to the left to lock.

4.4 Drive belt

Check the drive belt for wear every month, after 100 op-

erating hours and at the end of each season; renew if

necessary.

Checking/renewing the drive belt

1. Unscrew 4 screws

(1).

2. Remove drive

(2)

completely.

3. Checking the drive belt and renewing if necessary
4. Reinstall drive

(2).

«
...
25
26
27
28
29
...
»

Содержание Vento





















































Отзывы:

Нет отзывов

Похожие инструкции для Vento

Бренд: Facit Страницы: 51

Бренд: IDTECH Страницы: 8

Бренд: Land Pride Страницы: 32

Бренд: McGREGOR Страницы: 4

Бренд: IDTECH Страницы: 15

Бренд: Boss Snowplow Страницы: 2

Бренд: RIB Страницы: 4

Бренд: Corzus Страницы: 3

Бренд: Echo Страницы: 20

SafeQ USB Card Reader v3

Бренд: Ysoft Страницы: 7

Access manager 92 32

Бренд: Kaba Страницы: 53

WORKCENTRE 7120

Бренд: Xerox Страницы: 32

Cube Card Reader 190

Бренд: Nedap Страницы: 4

imperial Digiplex Evo R910

Бренд: Paradox Страницы: 2

Бренд: EQUIFAB Страницы: 7

Бренд: 3MillID Страницы: 4

ImageMate SDDR-92

Бренд: SanDisk Страницы: 44

Бренд: Vink Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды