LEHNER Vento Скачать руководство пользователя

Страница: 11 / 52

Mounting and start-up

Vento

1.0

11 / 52

Before start-up, make sure that the hopper on the

Vento

has been firmly bolted in place. To do this, check the four

knurled screws

(1).

Filling

1. Make sure that the spreader and blower are

switched off.

2. To fill the spreader, release the rubber clamping

band

(2)

on the hopper and remove the cover

(3).

3. Make sure that suitable rotary valves are fitted ac-

cording to the spreading material table, and that the

load relief roof of the agitator has been mounted cor-

rectly.

4. Fill the spreading material, making sure that no for-

eign bodies or impurities get into the hopper.

Before closing the hopper, make sure that the

seal is in place all round between the hopper

and the hopper cover.

6. Close the hopper with the four rubber clamping

bands

(2)

making a firm seal.

Warning!
Incorrect filling will lead to incorrect dosing applications.

•

The hopper cover must be closed during operation, in order to avoid incorrect dosing applications.

Содержание Vento





















































Результаты поиска

Содержание Vento

Отзывы:

Похожие инструкции для Vento

Бренды по названию

Популярные бренды

LEHNER Vento, Руководство по эксплуатации с перечнем запасных частей

Результаты поиска

Содержание Vento

Отзывы:

Похожие инструкции для Vento

Бренды по названию

Популярные бренды