LEHNER Vento Скачать руководство пользователя

Страница: 9 / 52

Mounting and start-up

Vento

1.0

9 / 52

2.3 Electrical connection

Caution!
Risk of short-circuit and injury when working on the battery and electrical system!
Electrical current flowing through the body can cause cramps, ventricular fibrillation,

heart stoppage and internal burns. Risk of burns due to arcing caused by short circuits.

•

Protect the battery against damage and moisture.

•

Disconnect the electrical power supply before starting work on the battery and electrical system.

•

Use suitable tools so as to avoid short circuits.

•

Sure that the cables are routed without tension, kinking and chafing, and also avoid bending them
around sharp edges.

•

During all work on the battery, please comply with the regulations of the vehicle manufacturer in
question.

•

Only use original cables, or ones approved by the manufacturer.

•

Always push on the cap and lock it to protect electrical connections against damage.

Advice!

Faulty cables or cables with incorrect dimensions can lead to malfunctions and damage to the spread-

er. Any changes to cable or plug connections without factory approval automatically invalidates the entire

warranty.

Changes to cables undertaken by the customer are taken into account in the case of repair. Only use original ca-

bles, or ones approved by the manufacturer. You must consult with the manufacture before carrying out any cable

modifications. Power loss must be taken into account when extending cables. A poor power supply may prevent you

from achieving the desired blower speed. Also, this could lead to intermittent complete failure.

2.3.1 Technical data, electrical system

Operating voltage

12 to 15 V

Fuse

25 A

Speed range

20 to 120 rpm

Power consumption of motor

8.5 A

Operating temperature

10 to +50 °C

Storage temperature

-10 to +50 °C

Battery cable

minimum 6 mm²

2.3.2 Mounting the control panel

1. Mount support for the control panel in the vehicle cabin.
2. Plug the control panel cable into the 3-pin socket

(1)

of the supplied battery cable.

Connect connection

(2)

to the negative terminal of the battery (not to the bodywork).

Содержание Vento





















































Результаты поиска

Содержание Vento

Отзывы:

Похожие инструкции для Vento

Бренды по названию

Популярные бренды

LEHNER Vento, Руководство по эксплуатации с перечнем запасных частей

Результаты поиска

Содержание Vento

Отзывы:

Похожие инструкции для Vento

Бренды по названию

Популярные бренды