LEHNER Vento Скачать руководство пользователя страница 13

Страница: 13 / 52

Operation

Vento

1.0

13 / 52

Changeover using AUTO key

l FV

Manual mode

1. Manual operating mode
2. Current speed of the rotary feeder valve
3. Dosing OFF: Rotary feeder valve drive motor off

Dosing ON: Rotary feeder valve drive motor running

3.4 General setting possibilities and displays

The control element can be used to make the following settings:

•

Language

•

Displaying product lists and deleting products

•

Qty. adaptation

•

Calibrating the wheel sensor

•

Setting the EHR signal

•

Entering the calibration values

•

Creating products

3.4.1 Language

Switch off the spreader.

Press the

key, the

key and the On/Off key simultaneously.

Keep all three keys pressed for about 3 seconds.

L ng g
Engli

Press the key to set the language.

L ng g
Engli

Use the On/Off key to exit the menu.

3.4.2 Displaying product lists and deleting products

Switch off the spreader.

key, the

key and the On/Off key simultaneously.

Keep all three keys pressed for about 3 seconds.

L ng g
Engli

Содержание Vento





















































Результаты поиска

Содержание Vento

Отзывы:

LEHNER Vento, Руководство по эксплуатации с перечнем запасных частей, Страница: 13 / 52

Результаты поиска

Содержание Vento

Отзывы: