LAVAMAC GA120L Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 85

background image

Operating Instructions

Part No. 70476501ENR7

69

Figure 33

NOTE: The window display will flash. Press STOP/
RESET twice (within three seconds) to end the
cycle and reset the control to idle status. To restart
the tumble dryer, CLOSE door and press START
pad.

IMPORTANT: If the loading door or lint panel door
is opened during the cycle, the heating system
will shut off and the motor will stop. To restart the
cycle, both doors must be closed and START pad
must be pressed.

4. When the cycle is complete, open door and remove the

laundry.

WARNING

To prevent the risk of fire, remove laundry
immediately in case of power failure.

W779

NOTE: This machine includes an anti-wrinkle/
extended tumble feature. After the drying cycle
is complete, the cylinder will tumble without heat
every few minutes. The intermittent tumbling will
continue for one hour or until the door is opened.

G and K Models with RM Control Suffix

1. To use an Automatic Cycle, press a TEMPERATURE pad.

Select HIGH, MED, LOW, DELICATE or NO HEAT for
items that should not be dried with heat. A light to the left of
the selected pad lights up.

HIGH

Temperature 180°F
(82°C)

MEDIUM

Temperature 160°F
( 71°C)

LOW

Temperature 140°F
(60°C)

DELICATE

Temperature 120°F
(49°C)

Figure 34

2. To use a Time Dry or Custom Cycle, refer to the

Programming Manual.

3. Select REVERSING or NONREVERSING cylinder

rotation setting.

Figure 35

4. Press START pad to start tumble dryer.

Figure 36

NOTE: All pads can be pressed in any sequence
without damaging control or tumble dryer. To stop
the tumble dryer at any time, open the door or
press STOP.

Figure 37

NOTE: The window display will flash. Press STOP
twice (within three seconds) to end the cycle
and reset the control to idle status. To restart the
tumble dryer, CLOSE door and press START pad.

IMPORTANT: If the loading door or lint panel door
is opened during the cycle, the heating system
will shut off and the motor will stop. To restart the
cycle, both doors must be closed and the PUSH
TO START button must be pressed in.

«
...
67
68
69
70
71
...
»

Содержание GA120L






















































































Отзывы:

Нет отзывов

Похожие инструкции для GA120L

Бренд: ziltek Страницы: 6

Бренд: DAN DRYER Страницы: 12

Бренд: SEVERIN Страницы: 1

Бренд: Scarlett Страницы: 12

Бренд: DCG Страницы: 16

Бренд: FERREX Страницы: 20

Professional 1 Slim

Бренд: Taurus Страницы: 68

Бренд: Summit Страницы: 15

Бренд: Frymaster Страницы: 37

Bravetti Professional K4321B

Бренд: Euro-Pro Страницы: 16

Бренд: e-Ware Страницы: 9

Бренд: Hitachi Страницы: 200

iQ300 WK14D321HK

Бренд: Siemens Страницы: 32

Бренд: Siemens Страницы: 56

Бренд: Siemens Страницы: 64

Бренд: TecLime Страницы: 26

Бренд: Mediclinics Страницы: 10

Бренд: Mediclinics Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды