LAVAMAC GA120L Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 85

background image

Operating Instructions

Part No. 70476501ENR7

65

Operating Instructions

Operating Instructions

WARNING

To reduce the risk of fire:

•

DO NOT DRY articles containing foam rubber or
similarly textured rubberlike materials.

•

DO NOT DRY plastics, anything containing wax
or chemicals such as mops and cleaning cloths,
or anything dry-cleaned at home with a dry-
cleaning solvent.

•

DO NOT TUMBLE fiberglass curtains and
draperies unless the label says it can be done. If
they are dried, wipe out the cylinder with a damp
cloth to remove particles of fiberglass.

W076

WARNING

To reduce the risk of serious injury, allow cylinder
to stop before cleaning lint screen.

W412

Emergency Stop Button On CE Models

All CE approved tumble dryers are factory equipped with an
emergency stop button located on the front panel. Refer to
Figure 23 .

1 Emergency Stop Button

Figure 23

To operate emergency stop button:

•

Press red emergency stop button to stop all action.

•

To restart machine, pull red emergency stop button out and
press START pad or button.

NOTE: Activation of the emergency stop button
stops all machine control circuit functions, but
DOES NOT remove all electrical power from
machine.

Operating Instructions

WARNING

To reduce the risk of fire, electric shock, or
injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS before operating this appliance.

W727

IMPORTANT: This appliance shall not be used to dry
off solvents or dry cleaning fluids.

1. Clean Lint Screen/Compartment

a.

Remove any accumulated lint from the lint screen and
compartment.

b.

Close panel tightly against tumble dryer frame and lock
panel securely, if applicable.

IMPORTANT: Clean lint screen and lint
compartment daily. Failure to clean the lint screen
daily will result in higher than normal temperatures
that may damage laundry.

WARNING

To reduce the risk of fire and risk of lint
collecting in exhaust duct, do not operate
tumbler without lint filter in place.

W772

2. Load Laundry

a.

Open loading door and load cylinder with laundry.
Maximum drying load is:

Model

Pound (Kg)

120

120 (54.4)

170

170 (77.1)

«
...
63
64
65
66
67
...
»

Содержание GA120L






















































































Отзывы:

Нет отзывов

Похожие инструкции для GA120L

Бренд: GE Страницы: 44

Бренд: UFESA Страницы: 42

Fashion Ultraviolet

Бренд: Taurus Страницы: 72

Бренд: inventum Страницы: 32

Бренд: Taurus Страницы: 56

Бренд: GE Страницы: 32

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренд: GE Страницы: 32

ESSENTIALS COOLWALL FRYER

Бренд: Morphy Richards Страницы: 8

Бренд: Panasonic Страницы: 56

Бренд: Maestro Страницы: 48

Бренд: Vivax Страницы: 38

01.183023.01.001

Бренд: Princess Страницы: 58

01.182075.02.001

Бренд: Princess Страницы: 10

01.182065.01.001

Бренд: Princess Страницы: 88

TVFG 65C Futura

Бренд: Hotpoint Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды