LAVAMAC GA120L Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 85

background image

Adjustments

78

Part No. 70476501ENR7

TMB2359N

1 Door Strike

2 Adjustment Screws

Figure 45

Belt Drive

The drive assemblies consist of motors, belts, eyebolts and a step pulley.

The pulley diameters are sized to produce a cylinder speed of 37-39 RPM for 120 series models or 29-31 RPM for 170 and 200 series
models.

The step pulley assembly is used for speed reduction as well as a means of adjusting belt tension. The pulley mounting plate is
attached to the cabinet. The frame mounting plate has vertically slotted holes allowing up and down movement of the step pulley
mounting plate for belt adjustment.

Adjust the belt tension as follows:
1. Disconnect electrical power to the tumble dryer before

attempting any adjustments to the drive assembly.

2. Loosen pulley mounting plate bolts.

3. Loosen the upper nut on the final drive eyebolt.

4. Rotate the lower nut of the final drive eyebolt clockwise

until proper belt tension is achieved.

5. Rotate upper nut clockwise against the lower nut in order to

lock it into place.

6. Tighten pulley mounting plate bolts. Recheck belt tension.

7. If necessary, adjust the drive motor belt tension eyebolt

using a similar procedure.

8. Adjust blower belt tension on 120 series 50 Hertz tumble

dryers and all 170 series tumble dryers using a similar
procedure.

NOTE: Proper tensions for new belts are measured
with a Belt Tension Gauge:

Drive

Motor

Final Drive

Blower

Initial

After

Run-

in

Initial

After

Run-

in

Initial

After

Run-

in

120

60-70 45-55 70-80 55-65 60-70 50-55

170

60-70 45-55 70-80 55-65 75-80 60-65

200

60-70 45-55 70-80 55-65 65-70 55-60

Table 15

«
...
76
77
78
79
80
...
»

Содержание GA120L






















































































Отзывы:

Нет отзывов

Похожие инструкции для GA120L

Бренд: Lamona Страницы: 16

Бренд: ziltek Страницы: 6

Бренд: Maytag Страницы: 188

CellTec JAX-0300-00A

Бренд: CellPath Страницы: 20

Бренд: SCOTT MILLER Страницы: 13

Perfoma PYE4500

Бренд: Maytag Страницы: 9

Бренд: Alliance Laundry Systems Страницы: 88

Бренд: Gourmia Страницы: 16

Бренд: Flame Страницы: 2

CLEAN DRY HDR120

Бренд: Toto Страницы: 10

Бренд: Waring Страницы: 11

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 76

Бренд: Electrolux Страницы: 80

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 240

Бренд: Electrolux Страницы: 68

DV45K6200E(G) series

Бренд: Samsung Страницы: 216

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды