LAVAMAC GA120L Скачать руководство пользователя страница 37

Страница: 37 / 85

Installation

Part No. 70476501ENR7

1 Manometer

2 Pressure Tap

3 Burner Tube Attaching Screws

4 Gas Valve Flange

5 Gas Valve

6 Specified Pressure

Figure 8

2. Remove gas valve:

Remove the burner orifice(s) from the spud holder.

When converting from Natural Gas to L.P. Gas, the
left-most burner and orifice (viewed from front) must
be removed.

In place of the removed orifice, a blank orifice (Part
No. M400995) and a Burner Opening Cover (Part No.
M413099) must be installed.

3. Install the new, correct burner orifice(s). Refer to Figure 9

Burner Orifice and Table 1 . Torque each to 9 – 10 Nm.

4. Reinstall spud holder assembly to gas valve, making certain

burner orifice(s) are in line with burner tube opening. Refer
to Figure 9 Burner Orifice.

5. Commission tumble dryer for use.

NOTE: Blank burner orifices are Part No. M400995.

How to Adjust Gas Valve Governor/Regulator

1. Check gas burner orifice (manifold) pressure as follows.

Refer to Figure 8 .

2. Remove screw plug from pressure tap.

3. Connect a “U”-tube manometer (or similar pressure gauge)

to the burner orifice (manifold) pressure tap.

4. Start tumble dryer and note pressure once flame is burning.

Remove regulator cap and adjust regulator screw until the

burner orifice pressure per applicable table is achieved.
Replace regulator cap. Refer to Figure 8 .

5. Commission tumble dryer for use.

1 Size Stamped on Orifice

Figure 9 Burner Orifice

Содержание GA120L






















































































Результаты поиска

Содержание GA120L

Отзывы:

Похожие инструкции для GA120L

Бренды по названию

Популярные бренды

LAVAMAC GA120L, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание GA120L

Отзывы:

Похожие инструкции для GA120L

Бренды по названию

Популярные бренды