manualshive.com logo in svg

LAVAMAC GA120L, Установка, эксплуатация и обслуживание

Поделиться
Скачать
LAVAMAC GA120L Скачать руководство пользователя страница 67

Operating Instructions

  Part No. 70476501ENR7

  67

Figure 27

5.   Press and release START button to start tumble dryer.

Display will show minutes remaining before end of cycle.

Figure 28

NOTE: One touch drying is available for repetitive
loads. If the START button is pressed while the
machine is in Idle Mode, when the display is dark,
the tumble dryer will repeat the last drying cycle.
If the cycle time is adjusted before the cycle is
started, the time displayed when the start button
was pressed will be used for future cycles.

IMPORTANT: To stop the tumble dryer at any time
during the cycle, OPEN DOOR. If the loading door
or lint panel door is opened during the cycle, the
heating system will shut off and the motor will
stop. To restart the cycle, both doors must be
closed and the START button must be pressed in.

If the load cools to 90°F (32°C) before cool down time expires,
the control will flash “Lr” (load ready) in the heat time display.
If the door is not opened, the tumble dryer completes the
selected cool down time. If the door is opened after reaching
“Lr” temperature, the cycle will be terminated.

NOTE: If display shows an error code, refer to
Error Codes section.

6.   When the cycle is complete, open door and remove the

laundry.

WARNING

To prevent the risk of fire, remove laundry
immediately in case of power failure.

W779

NOTE: This machine includes an anti-wrinkle/
extended tumble feature. After the drying cycle
is complete, the cylinder will tumble without heat
every few minutes. The intermittent tumbling will
continue for one hour or until the door is opened.
Anti-wrinkle feature will tumble the load without
heat for 30 seconds every 2 minutes for 1 hour OR
until the loading door is opened.

Display

Definition

Corrective Action

OP

Open thermistor error

•

Check thermistor. Replace if inoperative.

•

Check wiring diagram between control and thermistor.
Refer to wiring diagram for proper wiring.

•

Check control. Replace if inoperative.

SH

Shorted thermistor error

•

Check thermistor. Replace if inoperative.

•

Check wiring between control and thermistor. Refer to
wiring diagram for proper wiring.

•

Check control. Replace if inoperative.

AF - 1

Airflow switch closed when cycle started

•

Check airflow switch. Replace if inoperative.

AF - 2

Airflow switch failed to close after cycle
started

•

Check airflow switch. Replace if inoperative.

Содержание GA120L






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды