background image

 

LAGUNATOOLS.COM 

 

Thank  you  for  investing  in  a  SuperMax  SuperBrush  by  Laguna  Tools.  

This brush sander is one of a family of unique machines proudly offered 
by  Laguna  Tools.    Every  Laguna  machine  is  engineered  for  years  of 

dependable service.  Please feel free to contact Laguna Tools if you have 
a  question  or  suggestion.    We  appreciate  working  with  you  and  your 

choice of a Laguna Tools machine for your shop.   
 

Regards, 
Torben Helshoj 

President & Founder Laguna Tools 

 

Dealer Machinery Warranty 

New  woodworking  machines  sold  by  Laguna  Tools  carry  a  two-year  warranty  effective 
from  the  date  of  dealer  invoice  to  consumer.  Machines  sold  through  dealers  must  be 
registered with Laguna Tools within 30 days of purchase to be covered by this warranty. 

Laguna  Tools  guarantees  all  new  machine  sold  to  be  free  of  manufacturers’  defective 

workmanship,  parts  and  materials.  We  will  repair  or  replace,  without  charge,  any  parts 
d

etermined  by  Laguna  Tools,  Inc.  to  be  a  manufacturer’s  defect.  We  require  that  the 

defective  item/part  be  returned  to  Laguna  Tools  with  the  complaint.  An  RMA  (return 
merchandise authorization) must be requested, from Laguna Tools, and included with any 
and  all  parts  or  machines  returned  to  Laguna  Tools  for  warranty  consideration.  Any 
machines returned to Laguna Tools must be returned with packaging in the same manner 
in  which  it  was  received.  If  a  part  or  blade  is  being  returned  it  must  have  adequate 
packaging to ensure no damage is received during shipping. In the event the item/part is 
determined  to  be  damaged  due  to  lack  of  maintenance,  cleaning  or  misuse/abuse,  the 
customer will be responsible for the cost to replace the item/part, plus all related shipping 
charges. This limited warranty does not apply to natural disasters, acts of terrorism, normal 
wear and tear, product failure due to lack of maintenance or cleaning, damage caused by 
accident, neglect, lack of or inadequate dust collection, misuse/abuse or damage caused 
where repair or alterations have been made or attempted by others. 

This manual applies to the SuperBrush 24 x 2 and 36 x 2.  Enter the model 

number  and  serial  number  below  for  quick  reference  when  ordering 

accessories, supplies or parts.   

 

Model: ___________ 
 

Serial: ___________ 
   

Laguna Tools                                          744 Refuge Way Suite 200           
Grand Prairie 

                                   TX 75050 

 
                    800-234-1976                   

www.lagunatools.com 

 

 

Содержание SuperMax SuperBrush 24 x 2

















































Отзывы: