Laguna Tools SuperMax SuperBrush 24 x 2 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 48

Laguna Tools SuperMax SuperBrush 24 x 2 Скачать руководство пользователя страница 15

LAGUNATOOLS.COM

15

IN ALL CASES, MAKE CERTAIN THE RECEPTACLE OR DISCONNECT IS

PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED
ELECTRICIAN CHECK THE RECEPTACLE OR DISCONNECT.

ASSEMBLY

This step requires a forklift.

The SuperBrush is heavy, be careful when

lifting and handling it with a forklift! Failure to comply may cause serious

injury and/or damage to the machine and/or property!

Tools/items Required:

9/16”

wrench

1/2

” wrench

5mm hex wrench
Power Cord and Plug (unless hard wiring into a disconnect)

To assemble your SuperBrush, follow these steps:
For your own safety, do not connect the machine to the power source until
the machine is completely assembled. Please also make sure that you read
and understand the entire manual.

1.  Make sure the eight locking set screws in the Table Support Castings are
tight.  Unbolt machine from pallet.  Using a forklift, lift the SuperBrush from
the pallet.  The forks should lift from under the conveyor support cross
members.  Be careful when placing the forks not to damage other areas or
wiring, Fig. 3 & 5.

«
...
13
14
15
16
17
...
»

Содержание SuperMax SuperBrush 24 x 2

















































Отзывы:

Нет отзывов