Lagler TRIO 900.65.00.100 Скачать руководство пользователя

Страница: 61 / 80

TRIO 01.04.2015
English / Englisch

9.6 SANDING PROBLEMS (WAVES, STRIPS,

GROOVES)

•

The floor was not vacuumed before sanding. The floor must

be vacuumed thoroughly always directly before each sanding

step.

•

The sanding medium is damaged or incorrect and must be

replaced.

ection 5.3, Changing the sanding media

•

Sanding plates: At least one of the flexible Velcro rings is

damaged and must be replaced.

ection 5.3, Changing the sanding media

•

Sanding plates: The sanding media are not centred or not

fixed properly to the sanding plates. This must be corrected

correspondingly.

Section 5.3, Changing the sanding media

•

The configurations of the three sanding plates differ from

each other. Always use three sanding plates with identical

configurations.

ection 5.3, Changing the sanding media

•

The sanding plates or milling discs are not mounted properly

and must be fixed correctly.

Section 5.2, Changing the sanding plates

•

The wheels are dirty or damaged and must be cleaned or

replaced.

•

The machine guidance is either too fast and must be slowed

down or it is executed with an irregular speed.

CAUSES OF FAULTS

Содержание TRIO 900.65.00.100

















































































Результаты поиска

Содержание TRIO 900.65.00.100

Отзывы:

Похожие инструкции для TRIO 900.65.00.100

Бренды по названию

Популярные бренды

Lagler TRIO 900.65.00.100, Руководство по эксплуатации

Результаты поиска

Содержание TRIO 900.65.00.100

Отзывы:

Похожие инструкции для TRIO 900.65.00.100

Бренды по названию

Популярные бренды