Lagler TRIO 900.65.00.100 Скачать руководство пользователя

Страница: 40 / 80

TRIO 01.04.2015

English / Englisch

MAINTENANCE WORK AND REPLACEMENT OF WEARING PARTS

Certain maintenance jobs ought to be performed from time to time,

at the latest, however, when damage is established or the red

LED of the pressure control sensor lights up. Use only LÄGLER

original spare parts. Perform the job in a clean, brightly lit working

environment and follow the directions given in this manual. In the

tool bag you will find all the tools needed for the jobs described

below.

7.1 CLEANING AND CARE

WARNING!

RISK OF FIRE from spontaneous combustion and the formation

of sparks while sanding:

•

There is a high risk of fire when sanding woods with a
large amount of resin, oiled or waxed floors or metal!

Therefore, the machine must always be cleaned carefully
directly after sanding!

•

Be certain to note the warning notices of the manufacturers
of paint, oil and wax!

Never use solvent-based cleaning agents!

Before starting work you should carry out the following care and

maintenance steps to guarantee proper machine function and a

first-class sanding result:

•

Check the sanding discs, flexible Velcro rings and rubber

plugs of sanding plate pulleys for damage.

•

Clean the wheels of the machine.

•

Carry out a visual inspection of the electrical equipment

(motor, switch, cables, plugs, couplings).

Содержание TRIO 900.65.00.100

















































































Результаты поиска

Содержание TRIO 900.65.00.100

Отзывы:

Похожие инструкции для TRIO 900.65.00.100

Бренды по названию

Популярные бренды

Lagler TRIO 900.65.00.100, Руководство по эксплуатации

Результаты поиска

Содержание TRIO 900.65.00.100

Отзывы:

Похожие инструкции для TRIO 900.65.00.100

Бренды по названию

Популярные бренды