manualshive.com logo in svg

Lagler TRIO 900.65.00.100, Руководство по эксплуатации, Страница: 32 / 80

Поделиться
Скачать
Lagler TRIO 900.65.00.100 Скачать руководство пользователя страница 32

TRIO  01.04.2015

English / Englisch

Fig. 42 

Tighten the counter nut again.

Fig. 41 

Use the TORX screwdriver to adjust the adjustment 
screw.

3

 

Loosen the counter nut (wrench size 13 mm) on the top edge 

of the milling disc for the holder to be adjusted. Use the TORX 

screwdriver in the shaft of the thread to keep the adjustment 

screw in position (fig. 40). 

4

 

Use the TORX screwdriver to adjust the adjustment screw. 

The indexable insert should be mounted in such a way that 

you can check the setting (fig. 41). 

5

 

Tighten the counter nut again. Use the TORX screwdriver 

again to keep the adjustment screw in position (fig. 42).

ATTENTION!

Make sure all screws are tight before you start working!

6  

Remount the milling discs as described in 

Section 5.2.2, 

Mounting the sanding plates

.

WORKING WITH THE TRIO

5

Fig. 40 

Loosen the counter nut (wrench size 13 mm) for 
the holder to be adjusted.

32

Содержание TRIO 900.65.00.100

















































































Отзывы:

Нет отзывов