Lagler TRIO 900.65.00.100 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 80

Lagler TRIO 900.65.00.100 Скачать руководство пользователя страница 56

TRIO 01.04.2015

English / Englisch

WARNING!

RISK OF DEATH from electrical shock:

Work on the electrical equipment is to
be conducted exclusively by a qualified
e l e c t r i c i a n ! T h e m a c h i n e m u s t b e
switched off and the power plug removed
from the socket during this work!
The circuit diagram valid for your machine
is located in the motor switch box!

RISK OF INJURY due to unsuitable parts:

Make sure that only original LÄGLER

®

spare parts and original LÄGLER

®

acces-

sories are used!

This section shows you how to remedy possible malfunctions. If

none of the measures listed here are successful, please contact

our service department, your retailer or your importer.

9.1 THE MACHINE DOES NOT RUN OR HAS

SWITCHED OFF AUTOMATICALLY

•

The machine is not connected to the electrical network.

Check the following items:

- Is the motor cable connected to the extension cable?

- Is the extension cable inserted into the power socket?

•

The cable plug of the sensor is not inserted into the on/off

switch.

Section 6.2, Reassembly after transportation,

point

4

•

The fuse inside the switch box of the motor is blown. The

reason for the blowing must be eliminated professionally and

the fuse be replaced. Two replacement fuses can be found

inside the switch box (part number in

Section 11, Spare parts

TRIO

).

•

The power socket is not properly connected. This error must

be corrected by an expert.

•

The electrical safety device of the electrical network

interrupted the electrical circuit, e.g. because

- too many electricity consumers are connected to the same

electrical circuit,

- improper electrical installation.

The causes for the error must be repaired by an expert.

•

The electrical network is not providing sufficient voltage

(undervoltage). Use a transformer if necessary (e.g. LÄGLER

®

part number 708.00.00.100 for 230 V).

Causes of faults

CAUSES OF FAULTS

9

56

«
...
54
55
56
57
58
...
»

Содержание TRIO 900.65.00.100

















































































Отзывы:

Нет отзывов