Kyocera KM-1650 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 280

Kyocera KM-1650 Скачать руководство пользователя страница 82

2DA/2DB-3.0

1-4-13

U053

*1: Optional. *2: Optional for 16 ppm model. Standard for 20 ppm model.

MAIN MOTOR

Increasing the setting makes the image longer in the auxiliary scanning direction, and decreasing it
makes the image shorter in the auxiliary scanning direction.

POLYGON MOTOR

Increasing the setting makes the image longer in the main scanning direction and shorter in the auxiliary
scanning direction; decreasing the setting makes the image shorter in the main scanning direction and
longer in the auxiliary scanning direction.

3. Press the start key. The value is set.

Interrupt copy mode

While this maintenance item is being performed, a VTC pattern shown below is output in interrupt copy mode.

1. Press the interrupt key. The machine enters the interrupt copy mode.
2. Press the start key. A VTC pattern is output.

To return to the screen for setting, press the interrupt key.

Correct values for an A3/11" x 17" output are:
A = 300

±

1.5 mm

B = 270

±

1.35 mm

Figure 1-4-1

Adjustment

1. Output an A3/11" x 17" VTC pattern in interrupt copy mode.
2. Measure A and B on the VTC pattern (Figure 1-4-1), and perform the following adjustments if they are

different from the correct sizes:
A: Drive motor speed adjustment
B: Polygon motor speed adjustment

Completion

Press the stop/clear key at the screen for setting. The screen for selecting a maintenance item No. is dis-
played.

Maintenance

item No.

Description

Display

Description

Setting range

Initial setting

RES1

Trailing edge registration motor correction
(paper feed from drawer)

0 to +5.0

0.0

RESB

Trailing edge registration motor correction
(paper feed from bypass tray)

0 to +5.0

0.0

RES2

Trailing edge registration motor correction
(paper feed from first paper feeder

*2

)

0 to +5.0

0.0

RES3

Trailing edge registration motor correction
(paper feed from second paper feeder

*1

)

0 to +5.0

0.0

RES4

Trailing edge registration motor correction
(paper feed from third paper feeder

*1

)

0 to +5.0

0.0

RESD

Trailing edge registration motor correction
(paper feed from duplex section

*1

)

0 to +5.0

0.0

«
...
80
81
82
83
84
...
»

Содержание KM-1650

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды