Kyocera KM-1650 Скачать руководство пользователя страница 161

Страница: 161 / 280

2DA/2DB-1

1-5-32

(15) Image is partly missing.

Causes

1. Paper damp.
2. Paper creased.
3. Dirty or flawed drum.
4. Dirty transfer roller.

Causes

Check procedures/corrective measures

1. Paper damp.

Check the paper storage conditions.

2. Paper creased.

Replace the paper.

3. Dirty or flawed drum.

Clean the drum or, if it is flawed, replace the drum unit (see page 1-6-38).

4. Dirty transfer roller.

Clean the transfer roller.

(16) Fixing is poor.

Causes

1. Wrong paper.
2. Defective pressure springs.
3. Flawed press roller.
4. Defective fixing heater.

Causes

Check procedures/corrective measures

1. Wrong paper.

Check if the paper meets specifications.

2. Defective pressure springs.

Replace the pressure springs.

3. Flawed press roller.

Replace the press roller (see page 1-6-45).

4. Defective fixing heater.

Replace the fixing heater (see page 1-6-46).

(17) Image is out of focus.

Causes

1. Defective image scanning unit.
2. Drum condensation.

Causes

Check procedures/corrective measures

1. Defective image scanning unit.

Replace the image scanning unit (see page 1-6-28).

2. Drum condensation.

Clean the drum.

Содержание KM-1650

























































































































































































































































































Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды

Kyocera KM-1650, Руководство по обслуживанию

Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды