Kyocera KM-1650 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 280

Kyocera KM-1650 Скачать руководство пользователя страница 102

2DA/2DB-3.0

1-4-33

U204

Setting the presence or absence of a key card or key counter
Description

Sets the presence or absence of the optional key card or key counter.

Purpose

To run this maintenance item if a key card or key counter is installed.

Setting

1. Press the start key. The screen for selecting an item is displayed.
2. Select the optional counter to be installed using the up/down cursor keys. The selected counter is dis-

played in reverse.

3. Press the start key. The setting is set and the screen for selecting a maintenance item No. is displayed.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U207

Checking the operation panel keys
Description

Checks operation of the operation panel keys.

Purpose

To check operation of all the keys and LEDs on the operation panel.

Method

1. Press the start key. The screen for executing is displayed.
2. COUNT1 is displayed and the leftmost LED on the operation panel lights.
3. As the keys lined up in the same line as the lit indicator are pressed in the order from the top to the bot-

tom, the figure shown on the touch panel increases in increments of 1. When all the keys in that line are
pressed and if there are any LEDs corresponding to the keys in the line on the immediate right, the top
LED in that line will light.

4. When all the keys on the operation panel have been pressed, all the LEDs light for up to 10 seconds.
5. When the LEDs go off, press the start key. All the LEDs light for 10 seconds again.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U233

Setting the ejection limit of the job separator
Description

When an optional job separator is installed, whether the limit of ejection to the job separator is 50 sheets for
A3/11" x 17" and 100 sheets for other sizes or 100 sheets for all sizes is set.

Purpose

To be set according to user request.

Method

Press the start key. The screen for selecting an item is displayed.

Setting

1. Select the item using the up/down cursor keys.

Initial setting: MODE0

2. Press the start key. The setting is set, and the screen for selecting a maintenance item No. is displayed.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

OFF

None

KEY-CARD

The key card is installed

KEY-COUNTER

The key counter is installed

Display

Description

MODE0

All size is limited to 100 sheets.

MODE1

A3/11" x 17" is limited to 50 sheets

«
...
100
101
102
103
104
...
»

Содержание KM-1650

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды