Kyocera KM-1650 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 280

Kyocera KM-1650 Скачать руководство пользователя страница 79

2DA/2DB

1-4-10

U027

Return of backup data
Description

Transfers the backup data of the EEPROM which was transferred with the U026 to flash memory.

Purpose

To use after the main PCB replaced.

Method

1. Press the start key. The screen for executing is displayed.
2. Select the EXECUTE using the up/down cursor keys. It is displayed in reverse.
3. Press the start key to transfer the backup data. The screen displays the result.

EXECUTE
CHECK SUM: ****
CODE : XXXX (See the table below)

4. Disconnect and connect the power plug.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U030

Checking motor operation
Description

Drives each motor.

Purpose

To check the operation of each motor.

Method

1. Press the start key. The screen for selecting an item is displayed.
2. Select the motor to be operated using the up/down cursor keys.
3. Press the start key. The operation starts.

*1: Optional. *2: Optional for 16 ppm model. Standard for 20 ppm model.

4. To stop operation, press the stop/clear key.

Completion

Press the stop key after operation stops. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Code

Description

0000

Processing ends correctly.

0203

Check sum does not agree when reading out from the EEPROM.

Display

Operation

MAIN

Drive motor (DM) operates

RES

Registration motor (RM) operates

T1

Drawer drive motor 1

*2

(DDM1) operates

T2

Drawer drive motor 2

*1

(DDM2) operates

T3

Drawer drive motor 3

*1

(DDM3) operates

EJE1

Eject motor rotates forward

EJE2

Eject motor rotates in reverse

«
...
77
78
79
80
81
...
»

Содержание KM-1650

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды