Kyocera KM-1650 Скачать руководство пользователя страница 152

Страница: 152 / 280

2DA/2DB

1-5-23

C6000

Broken fixing heater wire

In fixing warm-up, the time to reach
50

C/122

F exceeds 13.5 s, the time to

reach 100

C/212

F exceeds 10 s, the

time to reach the primary stabilization
exceeds 10 s or the time to reach the
secondary stabilization exceeds 24 s.

Fixing heater M or
S installed incor-
rectly.

Check and reinstall if necessary.

Broken fixing
heater M or S wire.

Check for continuity. If none, replace the fix-
ing heater M or S.

C6020

Abnormally high fixing unit ther-
mistor temperature

The fixing temperature exceeds 230

446

F for 40 ms.

Shorted thermistor. Measure the resistance. If it is 0

Ω

, replace

the thermistor.

Broken heater con-
trol circuit on the
power supply PCB.

Replace the power supply PCB and check
for correct operation.

C6050

Abnormally low fixing unit thermistor
temperature

The fixing temperature remains below
90

C/194

F for 1 s.

Poor contact in the
thermistor connec-
tor terminals.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.

Broken fixing ther-
mistor wire.

Measure the resistance. If it is

∞

Ω

, replace

the fixing thermistor.

Fixing thermistor
installed incor-
rectly.

Check and reinstall if necessary.

Fixing thermostat
triggered.

Check for continuity. If none, replace the fix-
ing thermostat.

Fixing heater M or
S installed incor-
rectly.

Check and reinstall if necessary.

Broken fixing
heater M or S wire.

Check for continuity. If none, replace the fix-
ing heater M or S.

C6400

Zero-crossing signal problem

The engine PCB does not detect the
zero-crossing signal for the time speci-
fied below. At power-on: 3 s Others: 5 s

Poor contact in the
connector termi-
nals.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.

Defective power
supply PCB.

Check if the zero-crossing signal is output
from YC2-5 on the power supply PCB. If not,
replace the power supply PCB.

Defective engine
PCB.

Replace the engine PCB if C6400 is
detected while YC2-5 on the power supply
PCB outputs the zero-crossing signal.

C7800

Broken external temperature ther-
mistor

The input voltage is 0.5 V or less.

Poor contact in the
humidity sensor
connector termi-
nals.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.

Defective humidity
sensor.

Replace the drawer PCB and check for cor-
rect operation.

Code

Contents

Remarks

Causes

Check procedures/corrective measures

Содержание KM-1650

























































































































































































































































































Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды

Kyocera KM-1650, Руководство по обслуживанию

Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды