Kyocera KM-1650 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 280

Kyocera KM-1650 Скачать руководство пользователя страница 81

2DA/2DB-3.0

1-4-12

U035

Setting folio size
Description

Changes the image area for copying onto folio size paper.

Purpose

To prevent the image at the trailing edge, or right or left side of the paper from not being copied by setting the
actual size of the folio paper used.

Method

Press the start key. The screen for setting is displayed.

Setting

1. Select the item to be set using the up/down cursor keys. The selected item is displayed in reverse.
2. Change the setting using the left/right cursor keys.

3. Press the start key. The value is set.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U051

Adjusting the amount of slack in the paper
Adjustment

See page 1-6-21.

U053

Performing fine adjustment of the motor speed
Description

Performs fine adjustment of the speeds of the motors.

Purpose

Used to adjust the speed of the respective motors when the magnification is not correct. Also speed adjust-
ment for each paper source.

Method

Press the start key. The screen for setting is displayed.

Setting

1. Select the item to be set using the up/down cursor keys. The selected item is displayed in reverse.
2. Change the setting using the left/right cursor keys.

Maintenance

item No.

Description

Display

Setting

Setting range

Initial setting

LENGTH DATA

Length

330 to 356 mm

330

WIDTH DATA

Width

200 to 220 mm

210

Display

Description

Setting range

Initial setting

MAIN

Drive motor speed adjustment

-5.0 to +5.0

0.1

POLY

Polygon motor speed adjustment

-5.0 to +5.0

0

EJE

Eject motor speed adjustment

-5.0 to +5.0

-0.5

RES

Registration motor speed adjustment

-5.0 to +5.0

-0.1

BYP

Motor speed adjustment
(for paper feed from bypass tray)

-5.0 to +5.0

-0.1

CAS

Drawer paper feed motor speed adjustment
(for paper feed from paper feeder)

-5.0 to +5.0

-0.3

DUP

Duplex paper feed motor speed adjustment
(in duplex mode)

-5.0 to +5.0

-0.3

EJE2

Eject motor speed
(optional ejection correction value in the case of
paper size of A3, B4, and 11" x 17")

-5.0 to +5.0

-1.3

EJE3

Eject motor speed
(optional ejection correction value in the case of
paper size other than those above)

-5.0 to +5.0

-1.5

EJE4

Eject motor speed
(ejection motor correction value at the time of
duplex inner ejection)

0 to +5.0

0.5

«
...
79
80
81
82
83
...
»

Содержание KM-1650

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды