Kyocera KM-1650 Скачать руководство пользователя страница 157

Страница: 157 / 280

2DA/2DB

1-5-28

(3) Image is too light.

Causes

1. Insufficient toner.
2. The transfer voltage is not output properly.
3. Dirty main charger wire.
4. Dirty main charger grid.

Causes

Check procedures/corrective measures

1. Insufficient toner.

If the display shows the message requesting toner replenishment,
replace the container.

2. The transfer voltage is not output properly. Clean or check the transfer roller (see page 1-6-42).

3. Dirty main charger wire.

Clean the main charger wire or, if it is extremely dirty, replace the main
charger unit (see page 1-6-40).

4. Dirty main charger grid.

Clean the main charger grid or, if it is extremely dirty, replace the main
charger unit (see page 1-6-40).

(4) Background is visible.

Causes

1. The developing bias voltage is not properly.
2. Dirty main charger wire.

Causes

Check procedures/corrective measures

1. The developing bias voltage is not prop-

erly.

Replace the high voltage PCB and check for correct operation.

2. Dirty main charger wire.

Clean the main charger wire or, if it is extremely dirty, replace the main
charger unit (see page 1-6-40).

(5) A white line appears longitudinally. Causes

1. Dirty main charger wire.
2. Foreign matter in the developing unit.
3. Dirty shading plate.

Causes

Check procedures/corrective measures

1. Dirty main charger wire.

Clean the main charger wire or, if it is extremely dirty, replace the main
charger unit (see page 1-6-40).

2. Foreign matter in the developing unit.

Check if the magnetic brush is formed uniformly. Replace the developing
unit if any foreign matter (see page 1-6-41).

3. Dirty shading plate.

Clean the shading plate.

Содержание KM-1650

























































































































































































































































































Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды

Kyocera KM-1650, Руководство по обслуживанию

Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды