Kyocera KM-1650 Скачать руководство пользователя страница 176

Страница: 176 / 280

2DA/2DB-1

1-6-7

Gear

Spring pin

Feed roller

Bushing

Feed roller

Stop rings

Screw

Paper feeder

Screw

(3) Detaching and refitting the feed roller (20 ppm model only)

Follow the procedure below to replace the feed roller.

Procedure

1. Remove the rear cover, right cover and front

left lower cover.

2. Remove the three screws and then remove

the main body from the paper feeder.

Figure 1-6-10-1

3. Open the drawer left cover.
4. Remove the two stop ring, gear and spring

pin from rear side of the feed roller.
When removing the gear, take care not to
lose the spring pin.

5. Slide the bearings in the front and rear of the

feed roller toward the inside, push the feed
roller once into the rear side of the machine,
and then remove it from the paper feeder.

6. Remove the two bushing from front and rear

side of the feed roller.

7. Replace the feed roller and refit all the

removed parts.

Figure 1-6-10-2

Содержание KM-1650

























































































































































































































































































Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды

Kyocera KM-1650, Руководство по обслуживанию

Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды