Kyocera KM-1650 Скачать руководство пользователя страница 155

Страница: 155 / 280

2DA/2DB

1-5-26

1-5-3 Image formation problems

(1) No image

appears
(entirely white).

(2) No image

appears
(entirely black).

(3) Image is too

light.

(4) Background is

visible.

(5) A white line

appears longitu-
dinally.

See page 1-5-27.

See page 1-5-28.

(6) A black line

appears longitu-
dinally.

(7) A black line

appears later-
ally.

(8) One side of the

copy image is
darker than the
other.

(9) Black dots

appear on the
image.

(10) Image is

blurred.

See page 1-5-29.

See page 1-5-30.

(11) The leading

edge of the
image is consis-
tently mis-
aligned with the
original.

(12) The leading

edge of the
image is spo-
radically mis-
aligned with the
original.

(13) Paper creases.

(14) Offset occurs.

(15) Image is partly

missing.

See page 1-5-30.

See page 1-5-31.

See page 1-5-32.

(16) Fixing is poor.

(17) Image is out of

focus.

(18) Image center

does not align
with the original
center.

See page 1-5-32.

See page 1-5-33.

Содержание KM-1650

























































































































































































































































































Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды

Kyocera KM-1650, Руководство по обслуживанию

Результаты поиска

Содержание KM-1650

Отзывы:

Бренды по названию

Популярные бренды