manualshive.com logo in svg

Kyocera KM-1650, Руководство по обслуживанию

Поделиться
Скачать
Kyocera KM-1650 Скачать руководство пользователя страница 159

2DA/2DB-1

1-5-30

(9) Black dots appear on the image.

Causes

1. Dirty or flawed drum. 
2. Dirty contact glass. 
3. Deformed or worn cleaning blade.
4. Dirty drum separation claws. 
5. Dirty heat roller separation claws.

Causes

Check procedures/corrective measures

1. Dirty or flawed drum.

Clean the drum or, if it is flawed, replace the drum unit (see page 1-6-38). 

2. Dirty contact glass.

Clean the contact glass.

3. Deformed or worn cleaning blade.

Replace the drum unit (see page 1-6-38).

4. Dirty drum separation claws.

Clean the drum separation claws.

5. Dirty the heat roller separation claws.

Clean the heat roller separation claws.

(10) Image is blurred.

Causes

1. Scanner moves erratically.
2. Deformed press roller.
3. Paper conveying section drive problem.

Causes

Check procedures/corrective measures

1. Scanner moves erratically.

Check if there is any foreign matter on the front and rear scanner rails. If 
any, remove it.

2. Deformed press roller.

Replace the press roller (see page 1-6-45).

3. Paper conveying section drive problem.

Check the gears and belts and, if necessary, grease them.

(11) The leading edge of the image is 

consistently misaligned with the 
original.

Causes

1. Misadjusted leading edge registration.
2. Misadjusted scanner leading edge registration.

Causes

Check procedures/corrective measures

1. Misadjusted leading edge registration.

Readjust the leading edge registration (see page 1-6-16).

2. Misadjusted scanner leading edge regis-

tration.

Readjust the scanner leading edge registration (see page 1-6-35).

Содержание KM-1650

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды