manualshive.com logo in svg

Kyocera KM-1650, Руководство по обслуживанию

Поделиться
Скачать
Kyocera KM-1650 Скачать руководство пользователя страница 43

2DA/2DB

1-3-19

1-3-7  Installing the key counter (option)

Key counter installation requires the following parts:
Key counter cover (P/N 2A360010)
Key counter retainer (P/N 66060030)
Key counter mount (P/N 66060040)
Key counter assembly (P/N 41529210)
Four (4) M4 x 6 bronze TP-A screws (P/N B4304060)
One (1) M4 x 35 round head screw (P/N B0004350)
Two (2) M3 x 6 bronze flat-head screws (P/N B2303060)
One (1) M3 bronze nut (P/N C2303000)
Key counter mounting plate (P/N 2C960100)
Key counter wire (P/N 2C960110)

Procedure

1. Fit the key counter socket assembly to the 

key counter retainer using the two screws 
and nut.

2. Fit the key counter mount to the key counter 

cover using the two screws, and attach the 
key counter retainer to the mount using the 
two screws.

Figure 1-3-31

Key counter retainer (66060030)

Key counter mount (66060040)

Key counter cover 
(2A360010)

M4 x 6 screws (B4304060)

M4 x 6 screws (B4304060)

M3 nut 
(C2303000)

M3 x 6 flat-head screws (B2303060)

Key counter socket assembly
 (41529210)

Содержание KM-1650

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды