manualshive.com logo in svg

Kyocera Mita 1900N - B/W Laser Printer, Руководство по эксплуатации

Поделиться
Скачать
Kyocera Mita 1900N - B/W Laser Printer Скачать руководство пользователя страница 84

e-MPS

1-70

e-MPS Configuration

You can change the following parameters for e-MPS operation:
• Maximum number of Quick Copy/Proof and Hold jobs
• Maximum space assigned to temporary code jobs
• Maximum space assigned to permanent code jobs
• Maximum space assigned to virtual mailboxes

The total amount of storage areas specified must not exceed the total 
size of the Microdrive. Otherwise, you may only be able to accommodate 
print jobs of a smaller amount of print jobs than specified.

Changing the Maximum Number of Quick Copy/Proof and Hold 

Jobs

This changes maximum number of Quick Copy/Proof and Hold jobs from 0 

to 50. The default is 32.

1

Press the 

MENU

 key.

2

Press the   or   key repeatedly until 

e-MPS >

 appears.

3

Press the 

>

 key. 

4

Press the   or   key repeatedly until 

>e-MPS Configuration > 

appears.

5

Press the 

>

 key. 

6

Press the   or   key repeatedly until 

>>Quick Copy

 appears.

7

Press the 

ENTER

 key. A blinking cursor ( 

 

 ) appears.

Option

Note

e-MPS

>

>e-MPS

>

 Configuration

>>Quick Copy

32

>>Quick Copy

32

Содержание 1900N - B/W Laser Printer































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды