manualshive.com logo in svg

Kyocera Mita 1900N - B/W Laser Printer, Руководство по эксплуатации

Поделиться
Скачать
Kyocera Mita 1900N - B/W Laser Printer Скачать руководство пользователя страница 56

Pagination

1-42

5

Press the 

ENTER

 key. 

6

Press the 

MENU

 key. The message display returns to 

Ready

.

Alternative Emulation for KPDL Emulation

The auto KPDL (

KPDL (AUTO)

) emulation enables the printer to 

automatically change the emulation mode according to the print job 

received. The alternative emulation can be selected using the operator 

panel. The default alternative emulation is 

PCL 6

.

1

Press the 

MENU

 key.

2

Press the   or   key repeatedly until 

Emulation

 appears. 

3

Press the 

ENTER

 key. A blinking question mark (

?

) appears.

4

Press the   or   key repeatedly until the message display indicated 

KPDL (AUTO)

 appears.

5

Press the 

ENTER

 key.

6

Press the 

>

 key. When 

> Print KPDL Errs

 is displayed, press the 

 or   key. The display cycles through the emulation in the following 

order:

PCL 6

 (default)

Line Printer

IBM Proprinter

DIABLO 630

EPSON LQ-850

7

Press the 

ENTER

 key. A blinking question mark (

?

) appears.

Emulation

 PCL 6

Emulation

?PCL 6

Emulation

?KPDL (AUTO)

>Alt. Emulation

?PCL 6

Содержание 1900N - B/W Laser Printer































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды