Kyocera Mita 1900N - B/W Laser Printer Скачать руководство пользователя страница 206

Страница: 206 / 286

Serial Interface (Option)

C-6

Serial Interface (Option)

Installing the optional serial interface board kit (IB-10E) in the printer

enables connection to a computer with an RS-232C or RS-422A standard

serial interface.

RS-232C Interface

Interface Signals

The pins of the printer’s RS-232C interface connector carry the signals

listed in table below. The table also indicates whether each signal is

incoming or outgoing with respect to the printer.

Brief descriptions of the signals follow.

FG - Frame Ground - (Pin 1)

This pin is connected directly to the printer frame.

TXD - Transmit Data - (Pin 2)

This output carries asynchronous data sent by the printer to the computer.

It is used mainly in handshaking protocols.

RXD - Receive Data - (Pin 3)

This input carries serial asynchronous data sent by the computer to the

printer.

RTS - Request To Send - (Pin 4)

This output is always held high (above 3 volts).

CTS - Clear To Send - (Pin 5)

DSR - Data Set Ready - (Pin 6)

Unused.

Pin

In/out

Signal

Description

Frame ground

Out

TXD

Transmit Data

RXD

Receive Data

Out

RTS

Request To Send

CTS

Clear To Send

DSR

Data Set Ready

Signal Ground

Out

DTR

Data Terminal Ready

Содержание 1900N - B/W Laser Printer































































































































































































































































































Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Похожие инструкции для 1900N - B/W Laser Printer

Бренды по названию

Популярные бренды

Kyocera Mita 1900N - B/W Laser Printer, Руководство по эксплуатации

Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Похожие инструкции для 1900N - B/W Laser Printer

Бренды по названию

Популярные бренды